TeleScoping Poles

.
.
.

Button Tip
(for McGill Changers)
.
.
.

Segment Buttons
(alternate segments double lock)
Fiberglass 
Lamp Changer Poles

Designed for commercial use, these TeleScoping Lamp Changer Poles are designed to be used by qualified personnel to change large wattage commercial lamps in overhead light fixtures.  Made with high-strength fiberglass, a full size 40-foot pole weighs only 7 lbs. 

Poles extend and lock for use at any length of segments extended.  Each segment extends about five feet, with every other segment able to double lock with the previous, allowing poles to be used fully locked at less than maximum length. 

Rubber covered fingers with garter springs on McGill lamp changers make changing a variety of lamp types simple. Hard-to-reach lamps are easily replaced without using ladders or platforms. A variety of styles and sizes is available to fit practically all commonly used lamps. Models for use with incandescent, mercury, metal halide, and sodium lamps. 

  • Garter spring grips lamps firmly 
  • Lightweight for ease-of-use and convenience 
  • Insulated to help protect against shock 
  • Changes lamps up to 40-ft height (poles sold separately) 
Each pole must be used with any one of a variety of McGill Lamp Changer heads for each type of commercial lamps. 

Made of dielectric fiberglass, new poles in original condition are designed resistant to electical flow to 100kV rms. 

Also available are poles designed for general purposes with a variety of tip-end attachments.  See Fiberglass TeleScoping Poles.

Maximum length of pole manageable by an individual with good physical strength is limited to 10 meters (~30 feet).  This is due to the nature of relative weight of the far end of the pole at distance.  Beyond 10 meters is beyond the reasonable limits of an individual's personal strength and ability to control the hook-end of the pole. 

When a pole extended more than 10 meters (30 feet)* is to be used, it is required to have the assistance of additional persons and use of counterweight on pole base is recommended. 

.
See Warnings & Utilization Notes and Pole Utilization Errata
Fiberglass, Aluminum, Carbon Fiber, Range Poles, GPS Poles, Measurement Sticks, Tripod System, J-Lock™ Mast
Lamp Changer Poles
Full Length Segments wt. Collapsed
Length
Base Tube
Diameter
part no. Price (US$)
10 ft 2 1.6 lbs 69 inches 0.9 inches L10 100.
15 ft 3 2.4 lbs 70 inches 1.0 inches L15 150.
20 ft 4 2.7 lbs 71 inches 1.2 inches L20 230.
30 ft * 6 4.6 lbs 74 inches 1.5 inches L30 350.
40 ft * 8 5.8 lbs 77 inches 1.7 inches L40 470.
.Order
Select McGill Lamp Changer:
(Required w Lamp Changer Pole)

150s-C
10-50watt LED
us$88

150-CA
15-100watt
us$88

151-CA
25-200watt
us$62

152-C
300-500watt
us$78

153-C
750-1500watt
us$82

163-C
50watt MercVapor
35-400watt Sodium
70-175watt
MetalHalide
us$102

161-C
75-250watt 
Mercury Vapor
50-1000watt Sodium
175-400watt
MetalHalide
us$74
MR-16, S-14,
R-20, PAR-20 
A-15, A-17, A-19, 
G-16½, G-18½ 
A-19, A-21, A-23, 
SL-18, R-20, PAR-20,
G-25, G-30, BR-30, 
P-25, PS-25, 
PS-30, PS-35 
PS-35, PS-40, 
G-40, G-48,
BR-40 
PS-52, G-48, G-64 E-17, E-18, E-27 
ED-17, ED-18, B-17
E-21, E-23, 
E-23½, E-25, 
E-28, ED-23½, 
ED-28, BT-28
Coil Spring
7013 7013 7013 7014 7014 7013 7013
Select McGill Lamp Changer:
(Required w Lamp Changer Pole)

154-C
1000-1500watt
400-1000watt
Mercury Vapor
us$79

158-C
400-700watt
Mercury Vapor
400-1000watt
MetalHalide
us$152

154XL-C
1000watt
MetalHalide
us$146

156-C
50-500watt
100-500watt 
Mercury Vapor
35-70watt
MetalHalide
us$113

155-C
500-1000watt Flood
400-750watt 
Mercury Vapor
us$122

159-C
400watt
Mercury Vapor 
Flood
us$165
T-16, T-18, T-20 E-37, BT-37, 
T-46, ED-37
BT-56 R-30, R-40, 
PAR-30, PAR-36, 
PAR-38, ER-30, 
ER-40
R-52, R-57 R-60
Coil Spring
7013 7014 7014+7019 7014 7019 7019
.Order
see functionsee function
.
T4-C
Special Changer
micro 
Halogen bulbs
100-500watt
us$165
INST_T4 .pdf

.
166-C
2-inch 
Suction Cup Changer
30-75watt
us$36

.
162-C
3¾-inch 
Suction Cup Changer
25-150watt
us$37
McNET w 166-CMcNET w std chgr
McNET
Lamp Changer Safety Net 
us$148
(T-4) (PAR-20, R-20, R-30, ER-30) (PAR-30, PAR-36, PAR-38) (shown w lamp changers, not included)
* WARNING:  Suction Cup Changer is prone to bulb coming loose during installation or removal. 
Always ensure bulb surfaces are wiped clean of dust build up and moisten suction cup before use.
.
Lamp Changer Accessories.

Broken
Lamp Base 
Remover
200
us$36

Broom Thread
Adapter
McBROOM
us$33

Camera
Adapter
McCAMERA
us$47

Universal Mount
Adapter ‡
McUNIV
us$56

Lamp Changer 
Replacement 
Coil Springs

7013 us$7
7014 us$8
7019 us$9 

Adapter for use of ABOVE 
Lamp Changers with 
(H-series poles w Universal Mount)
McGILL blank
McGill adapter 
AMcGILL
us$24
‡ for use w ONLY light weight pole tools
.

Storage Case
us$38.
.
Pole Base Counterweights
10 Lbs
10 Lb Weight Set
us$24.95
20 Lbs
20 Lb Weight Set
us$49.95
Order

Images not to scale.
Subject to mfgr availability; prices subject to change. 
All prices above for USA product in US$.  Plus shipping and applicable taxes, duties or tariffs.
OH resident's will be charged sales tax, recipients must pay any other applicable taxes, duties or tariffs.
All sections are designed to meet OSHA, ASTM F-711, IEC-855 & IEC-1235. 

Fiberglass, Aluminum, Carbon Fiber, Range Poles, GPS Poles, Measurement Sticks, Tripod System, J-Lock™ Mast
WARNING
Pole strength and durability are unknown.  However, manufacturer evaluations indicate impressive resistance to pole failure with nominal loads in hook end.  Poles are capable of being raised and lowered from horizontal to vertical while fully extended, without danger of pole failure or excessive bending. 
See Warnings & Utilization Notes and Pole Utilization Errata.

When a pole extended more than 30-feet (10 meters) is to be used, it is required to have the assistance of additional persons 
and use of counterweight on pole base is REQUIRED.

DANGER
Not recommended for use in the vicinity of electrical power, power lines or any other potentially electrical environment without proper additional safeguards, precautions and special personnel safety training.
Manufactured by GeoData Systems Management, Inc. and/or McGill Electrical Group, Inc. 
* Manufacturers assume no personnel liabilities what-so-ever in the use of these products. 
End user assumes full responsibility for any hazards, injury or deaths which may result from any proper or improper utilization of these poles.
.
INFO Fiberglass Lamp Changer Poles
For further information, Email or Call 1-440-888-4749 (M-F 9-5 EST)
top of page
Pole Utilization Errata


Home, Computers,Special Technologies, Company Info, Personnel, Clients & Projects, Contacts, E-mail
.©2017 GeoData Systems Management Inc., Berea, OH 44017-0366 USA