See Warnings and Pole Utilization Errata
Designed for special utility, these very long, very strong Carbon Fiber TeleScoping Poles are suitable for special use or in places up to 20 meters above ground (or sea) level. Made with high strength light weight carbon fiber, a 60 foot (19m) pole weighs 10.4 lbs (4.7Kg).
The pole may be used with a variety of tips: universal mount for implements and hooks fastened to the top segment with a toothed-ring wing screw fitting, GPS tip, or hollow Euro thread tip.
A variety of special tools are available including: camera mount, hooks, tools.
Custom fit tools or miniature electronic devices may be modified for custom mount, or to fasten to the button tip.
Tripod Gimbal System
For use with 40-foot plus Fiberglass TeleScoping Poles, T-Lock™ TeleScoping Poles, or Carbon Fiber poles, Tripod System allows perfectly balanced pole to be set in any position with fingertip control.
Light weight portable fiberglass tripod, with fully articulated Gimbal Mount, allows fully extended pole to be rotated any direction 360-degrees horizontal, and from 5-degrees below the horizon to full 90-degrees vertical.
In addition, pole in Gimbal Mount can be fully rotated on its own axis, allowing complete manipulative control of whatever is mounted at the tip of the pole.
A variety of special tools are available to be mounted to the tip of these poles, or custom devices, antenna, cameras, or sensors.
Designed for general utility, these TeleScoping Poles are suitable for personnel to place climbing lines, cable ladders or other special use items or equipment in places up to 50 feet (15.2m) above ground (or sea) level. Made with high strength fiberglass, a full size heavy duty 40 foot (12m) pole weighs only 8.6 lbs (3.9Kg).
The pole may be used with a variety of implements and hooks fastened to the top segment with a toothed-ring wing screw universal mount.
A variety of special tools are available including: tree pruner, pruning saw, camera mount, GPS mount, broom thread, or various hooks and other tools.
Custom fit tools or miniature electronic devices may be modified to fasten to the universal mount tip.
Designed for commercial use, these TeleScoping Lamp Changer Poles are designed to be used by qualified personnel to change large wattage commercial lamps in overhead light fixtures. Made with high strength fiberglass, a full size 40 foot (12m) pole weighs only 5.8 lbs (2.6Kg).
Rubber covered fingers with garter springs on lamp changers make changing a variety of lamp types simple. Hard-to-reach lamps are easily replaced without using ladders or platforms. A variety of styles and sizes is available to fit practically all commonly used lamps. Models for use with incandescent, mercury, metal halide, and sodium lamps.
Each pole must be used with any one of a variety of McGill Lamp Changer heads for each type of commercial lamps.
Lightweight and non-conductive, these multi-segment telescopic survey Range Poles are made with high strength dielectric fiberglass. Alternating red and yellow bands are spaced every 12-inches. Tip segment is equipped with a metal eyelet for attaching ribbon or flag. Fiberglass segments lock into position with a button lock mechanism. Poles are 1.2-inches in diameter, approximately 73-inches in length collapsed.
Both English (feet) or Metric (meter) available.
Lightweight and safe, these Measurement Sticks and Load Height Sticks are ideal for fast and accurate measurements of overhead lines, telephone and cable-TV lines, highway clearances, structures and bridges, and transport carriers.
Made with high strength fiberglass, they feature positive locking, spring-loaded buttons for fast and easy extension. They also feature eye-level reading at the top of the base section, so no calculations are required.
Optional tip end cross arms make measuring load height or clearances easy.
Both English (feet) and/or Metric (meter) available.
Stealth TeleScoping Poles™
Designed for military special forces, the T-Lock™ Stealth TeleScoping Pole™ is suitable for special operations to place climbing lines, cable ladders or other special use items or equipment in places up to 10 meters above ground (or sea) level. Made with light-weight, high-strength aluminum alloy, a full size 10 meter pole weighs little more than 13 lbs.
The pole may be used to place a grappling hook, light weight object, or other device able to be held in a variety of tip end fittings. Custom fittings, tools or miniature electronic devices may be designed for possible use with the final tube segment by special request.
These heavy duty aluminum alloy J-Lock™ TeleScoping Pole is designed for special purpose applications to hold up to 80 lbs of equipment at height.
Made of extruded aluminum alloy, these all metal poles and locks are extremely strong, durable and easy to use. Segments lock in place automatically with a simple twist when each segment is extended to full length.
J-Lock™ poles are produced large batch orders for custom manufactured applications.
Manufacturer assumes no personnel liabilities what-so-ever
in the use of these poles.
Pole Utilization Errata
Home, Computers, Special Technologies, Company Info, Personnel, Clients & Projects, Contacts, E-mail